Skip to content
Europlasma logo

Technology & Process

Low-pressure PECVD (Plasma-Enhanced Chemical Vapour Deposition) is a dry, solvent-free process. In a vacuum chamber, typically between 10 and 1,000 mTorr, an electromagnetic discharge turns a process gas into a stable, cold plasma that cleans, activates or polymerises a monomer into a nanocoating on every exposed surface, including inner surfaces of pores and fibres.

Activation grafts reactive groups onto the surface to raise surface energy before gluing, printing or bonding. Its effect lasts days to months, depending on material and storage. A plasma nanocoating is an actual polymer layer, covalently bonded to the substrate, that gives permanent functionality such as repellency, hydrophilicity or a barrier.

At low pressure, the plasma fills the whole chamber at near-room temperature. That is what lets it reach 3D parts, porous media and the inside of fabrics and membranes, in batch or roll-to-roll. For surface treatment of flat films at line speeds up to 500 m/min, atmospheric plasma is the better fit: see our sister company CPI.

Polymers and plastic parts, assembled electronics and PCBAs, nonwovens, technical textiles, membranes, foams and composites. Batch chambers range from 50 to 2,000 litres. Vacuum roll-to-roll systems handle webs from 10 to 180 cm wide and rolls up to 80 cm in diameter. If your material is not listed, contact us for an evaluation.

From 10 nm to 1 µm, depending on the coating: 10–200 nm for PlasmaGuard® S, below 1.5 µm for the PlasmaGuard® X multilayer barrier. The layer is invisible and leaves colour, hand, breathability, acoustics and dimensions unchanged.

It depends on chamber size, load and target coating. Cleaning and activation are short cycles; functional coatings take longer. We specify cycle time and throughput for your part or roll after a feasibility trial.

Repellency & Barrier

PlasmaGuard® grows from the vapour phase as a layer a few hundred nanometres thick, versus tens of micrometres for liquid coats. There are no solvents and no curing step. PlasmaGuard® S is Z-axis conductive, which reduces connector masking, and it preserves breathability and acoustic performance.

Yes. PlasmaGuard® S and PlasmaGuard® X are 100% PFAS-free: no fluorine, chlorine, bromine or iodine. They comply with REACH (SVHC), RoHS and WEEE.

Yes. Nanofics 110 is a fluorinated hydrophobic and oleophobic coating, with a water contact angle above 110° and an oil grade above 4, for filter media and fabrics that require maximum oil repellency. We advise which option fits your application and regulatory constraints.

PlasmaGuard® S and X deposit a PFAS-free barrier a few hundred nanometres thick from the vapour phase, on fully assembled boards. There is no solvent, no curing, and Z-axis conductivity reduces connector masking.

Wettability & Biofunctional

From below 10° with the hydrophilic Nanofics 10 coating to above 105° with PlasmaGuard® S, on parts, membranes and textiles.

PlasmaGuard® S complies with ISO 10993-5 (cytotoxicity). For other coatings and medical applications, we support your biocompatibility testing on the final device. Validation of the finished device remains with the manufacturer.

Plasma coatings are covalently bonded to the substrate: they do not wash off and leave no leachables or extractables. Durability under washing, sterilisation and ageing depends on substrate and coating, and we validate it on your product.

Untreated polymer chips are hydrophobic, and simple plasma activation fades within days to months. A plasma-deposited hydrophilic coating, such as Nanofics 10 with a water contact angle below 10°, is covalently bonded and gives stable capillary flow, applied in one dry step that reaches into the microchannels.

Cleaning & Activation

No. Low-pressure plasma is cold and acts only on the outermost surface. Bulk mechanical and thermal properties are preserved. Etching removes material only when intended, in a controlled way, up to 1 µm.

From days to months, depending on the material and storage conditions. For best results, bond, print or coat soon after treatment. Where a permanent effect is needed, a plasma nanocoating is the better choice.

Vacuum plasma activation raises surface energy by grafting reactive groups onto the surface, in a short, dry cycle that reaches every recess of the part. Bond, print or coat soon after treatment, as the effect lasts days to months.

Working with Us

Yes. We run feasibility trials on your parts or rolls in our lab and industrial-scale machines, then scale up step by step. To request a trial, send us your material, dimensions and target property.

Both. We develop the process, coat your parts or rolls as a service, build turnkey batch and roll-to-roll systems with on-site support, and supply the process chemistry. Complete converting lines are built with our sister company Spoolex.

From sample parts and small evaluation rolls to full production runs. For continuous high volumes, we can build a system for your own plant. Contact us with your part size, roll dimensions and annual volume.

Europlasma NV, De Bruwaan 15, 9700 Oudenaarde, Belgium, part of the Plasmalex Group. We serve customers worldwide through local agents. Europlasma NV is not affiliated with Europlasma S.A. (France).

Still have questions?

Discuss your materials, target surface properties and production requirements with our plasma process engineers.

Talk to an engineer

Part of

Plasmalex Group

Europlasma NV, Oudenaarde, Belgium — part of the Plasmalex Group. One of four specialized companies within the group, delivering industrial solutions in plasma surface treatment technology.